****** - Verified Buyer
4.5
These were incredibly easy to install and adjust! I tried it on the outer rings and it was too loose, adjusted to the inner and voila it was done! I’ve gotten several compliments on the wheels. For the price it makes the vehicle look so much better. These were supposed to hold me off until I put better wheels on but I actually like the look of them!Like them. On my Nissan leaf but one popped off that same day?Our 14 year old put this on his sister's car. Can't speak for durability yet as she has not hit a curb yet ;)The only thing I have to say is it is a bit of a pain to install but can be done. One did fall off though after driving the hour after it was put on. The rest are fine.I installed these in a few minutes and they've stayed on for a few months. I drive on horrible roads in downtown Chicago and was skeptical that they would stay in but so far it's good. They look pretty cool too. Only problem was they sent me the flat black ones instead of chromeIt was hard to get the covers to fit on my car. I usually have no problems but it gave me a little struggle. I suggest you make sure its clipped on because if I hadn't checked I would of lost a cover. I thought it was snapped on but I guess it popped back out. It didn't make my car look fancy but I needed some new ones real quick.Love the looks of these hubcaps and there durable.just make sure You really adjust the tension ring or You will loose a hubcap!A bit difficult to actually install them on the auto wheels; however, once installed they look great and are secure.Like the others said, 5 stars for good design, a nice shiny black, in addition, a good quality of flexible plastic and not too friable, but 3 stars for the metal tender ring, it just a little too short, to give a good tension and even in position No.3 for wide wheels. To avoid return everything, studying everything, I found my solution. In addition, the only document provided is the adjustment 1, 2, 3 and nothing to indicate that it is necessary to install the ring inside, fortunately I know it, it would have been better to add a simple description and additional picture, I hope that the supplier may consider it. To be certain that the ends of the rings would remain well in one’s ajustement, I preferred to use the ajustement No.1 fit, because the ring goes further inside of adjustment. After, I cut 2 inches of a black tape for electricity and wrap each small ribbon to each retainer and put the ring back in place. It get tension similar to other hub-caps, but, as I do with all others my hub-caps, I always add 2 ''black tie-raps'' U.V. sun resistant, one opposite of the other, because even the best hub-caps are always possible to lose one of them driving in a curve or to have a flat tire. I use of long-nose-pliers and 11-inch "black tie-raps", with long-nose-pliers, it’s easier to grab of the return of the tie-rap and use cutting-pliers to remove the end of the 'tie rap'. You may follow my steps with 12 attached photos. Greetings!+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++Comme les autres disaient, 5 étoiles pour un bon design, un beau noir brillant, en plus d’une bonne qualité de plastique flexible et non trop friable, mais 3 étoiles pour l’anneau tender en métal, est juste un peu trop court, pour donner une bonne tension et même en position No.3 pour des roues larges. Pour éviter de tout renvoyer, en étudiant le tout, j’ai trouvé ma solution. De plus, le seul document fourni est l’ajustement 1, 2, 3 et rien pour indiquer qu’il faut installer l’anneau à l’intérieur, heureusement que je le sais, il aurait été préférable d’ajouter une simple description et d’image supplémentaire, j’ose espérer que le fournisseur pourra le considérer. Pour être certain que les fins des anneaux resteraient bien dans on ajustement, j’ai préféré utiliser l’ajustement No.1, parce que l’anneau va plus loin dans l’ajustement. Après, j’ai coupé 2 pouces d’un ruban noir pour l’électricité et enrouler chaque petit ruban à chaque pièce de retenue et remit l’anneau en place. J’ai eu une tension similaire à d’autre enjoliveurs, mais, comme je fais avec mes autres enjoliveurs, j’ajoute toujours 2 ‘’black tie-raps’’ résistant aux U.V. du soleil, un opposé à l’autre, parce que même le meilleur enjoliveur sont toujours possible d’en perdre un en conduisant dans une courbe ou d’avoir un pneu crevé. J’utiliser de pince à long nez et des ‘’tie raps’’ de 11 pouces, avec les pinces à long nez, c’est plus facile d’agripper le retour du ‘’black tie-rap’’ et utiliser des pinces coupantes pour enlever la fin du ‘’tie rap’’. Vous pouvez suivre mes étapes avec mes 12 photos attachées. Salutations!Bought these to cover up the steel rims in my winter tires. They hold really tight compared to some other covers I used, so there are no concerns with losing them. These are fantastic and look great. I got comments where people thought that they were rims. Note that the stickers I bought for my vehicle are sold separately.Had to get second set sent out to me, first had damage to holding tabs. Return was painless. Second set went on well, there were some issues with the lugnuts pushing on the centre cap. They look sharp.East to work with. Suggest you put a plastic tie to hold to wheel, it will survive car washes.Great hub caps look sweet as u can see , but they need to make them fit tighter might loose one.. will order them again, but just tweek that problem...
